1.一般事项
General requirements
1.1 适用范围Scope of Application
本插座适用于打印机、彩色液晶电视接收机、电脑以及网络等电子设备 外接数字信号装置之用。
This socket is used by color TV, component stereo, video disc players, computers and equivalent electronic equipment to connect with external audio and video device.
1.2 标准状态 Standard State
除另规定外,测量应在以下状态进行:
The test should be tested in the following state unless otherwise specified
温度: 15℃ ~ 35℃
Temperature: 15℃ ~ 35℃
相对湿度: 45% ~ 70%
Relative Humidity: 45% ~ 70%
气压: 86Kpa ~ 106 Kpa
Air Pressure: 86Kpa ~ 106 Kpa
1.3 使用温度范围：-25℃ ~ +70℃
Operating Temperature Range：-25℃ ~ +70℃
1.4 环保要求：符合欧盟RoHS 指令的环保要求。
Environmental Requirement：Comply with the EU environmental requirements ofRoHS directive
2. 额定规格
Rated voltage and current
a.额定电压为：（AC、DC、34 V）
Rated voltage: AC, DC, 34V
b.额定电流为：2.0 A
Rated current: 2.0 A
3. 测试要求
Test Requirements
3.1 外观、机械性能
Appearance & Mechanical Performance:
*******电子有限公司 ***** ELECTRONICS CO.,LTD
测试项目(Items) 测试方法(Test Method) 测试要求(Requirement) a：插座的金属零件表面应清洁、 无锈蚀和镀层起层现象，塑料件 应无肿胀气泡和裂缝。 b：符合产品图尺寸（附外形图） 外观、尺寸 a：目视 A Appearance、 Dimension a：The surface of the metal parts shall be kept clean, restless, free of aliquation, and free of swelling, bubble or crack for plastic parts. b: Confirms with product outline drawing（see attachment） b：卡尺 a：by visual observation b：beam calipers 插拔力 B Insertion/withdrawal force 按中国部标：GB5095.7 试验13b 进行。用测量误差不大于10%的推拉式测力器或弹簧秤，法插入力/拔出力： 码沿轴向方向进行测量 10~35N 范围内 Perform the measurement as per Test 13b, China ministerial standardGB5095.7.use push-pull force meter or spring of ±10% or lower error to measure the force, putting the poise along axial direction. The inserting force and pulling force of plugs shall be within 10~35N. 互换性 C Interchangeability 用同规格插塞插入和拔出 Plug in and plug out in the same specification interface 能互换自如 Be able to exchange each other. 3.2 电气性能
Electrical Performance 测试项目(Items) D 接触电阻Contact Resistance 测试方法(Test Method) 测量应按中国部标：GB5095.2 的“试验2a：接触电阻-毫伏法”规定的方法来测试每一接触件与测试量规之间的接触电阻。测量循环次数最少为5 次。 The contact resistance etween contact points and corresponding contact parts should be tested in the method as described in “test 2a: contact resistance-millivoltage method” in national standard GB5095.2.，the test cycle index should be at least 5 times 测试要求(Requirement) 插座接触电阻： 测试前≤30 mΩ 测试后≤50 mΩ The Contact Resistance should be ≤30 mΩ, before test, ≤50 mΩ after test. E 绝缘电阻 Insulation Resistance 插座在相互不接触的各导电部位之间的绝 缘电阻 试验电压为：DC150±15V 恒定温热为：DC100±15V Test the insulation resistance between 绝缘电阻≥1000MΩ， 绝缘电阻≥10MΩ Insulation Resistance ≥1000MΩ. Insulation Resistance *******电子有限公司 ***** ELECTRONICS CO.,LTD
neighboring contact parts of the socket and bottom plate. Damp Heat, Steady state: DC100±15V ≥10MΩ F 耐压 Withstand voltage 插座应按中国部标：GB5095.2 的“试验4a： 耐压试验方法，进行试验 试验电压为常态：50Hz AC750V 恒定湿热：50Hz AC150V 时间为：60±5s The socket should be tested following the method as described in “test 4a:voltage withstand test method” in China national standard GB5095.2, Testing voltage：50Hz AC750V Damp heat, steady state: 50Hz AC150V Time：60±5s 无击穿、飞弧现象 泄露电流不超过1.0mA Free of flashover or breakdown during the test, leakage current shall not exceed 1mA. 3.3 环境要求 Environmental Performance 测试项目(Items) G 温度骤变 测试方法(Test Method) 测试要求(Requirement) 外观无损伤 应符合绝缘电阻之要求 No breakdown in appearance, insulation resistance shall meet requirement. 按中国部标：GB5095.6 的试验11α规定的 方法进行试验 Sharp variation of 插座应能承受温度为-10~+70℃ temperatur暴露时间为t =30 分 5 次温度循环作用 e The socket shall withstand –10~+700C temperature, exposed time t1=30min, 5 times of temperature cycling, as described in Test 11a GB5095.6 H 恒定湿热 插座应能承受相对湿度为90%～96% Damp heat, 试验温度为：40±2℃ 持续96 小时的恒定湿热作用 steady state The socket shall be able to withstand 90%~96% relative humidity, test temperature is: 40±20C, continuously perform constant wet and thermal treatment for 96 hours. 1.外观无损伤 2.符合接触电阻、绝缘电阻、耐压 要求 1. No breakdown in appearance 2.Contact resistance, insulation resistance, Withstand voltage shall meet requirements. I 盐雾试验 Salt fog corrosion 温度为：35±2℃ 氯化钠溶液浓度为： 5±1%(重量) 时间：连续喷雾24 小时 a. temperature: 35 ± 20C; b. concentration of sodium chloride (NaC1): 5 ± 1% (weight); c. spray continuously for 24 hours. 金属表面无严重锈蚀 The metal surface shall free of serious rust corrosion J 高温试验 低温试验 温度为+85℃ 96h 温度为-25℃ 96h 1.外观无变形 2.符合接触电阻、绝缘电阻、耐压 *******电子有限公司 ***** ELECTRONICS CO.,LTD
High-temperature test Low-temperature test Temperature: +85℃ 96h Temperature: -25℃ 96h 要求 1.No deformation in appearance 2.Conform to contact resistance, insulation resistance, voltage requirements 3.4 焊接性能 Welding performance 测试项目(Items) K 可焊性 Solderability 测试方法(Test method) 接触件的可焊性，按中国部标：GB5095.6 的“试验12a：锡焊槽润湿法可焊性”规定 的方法进行试验 焊接温度：245±5℃ 浸锡时间：3±0.5S The solderability of contact parts shall be tested following the method “solderability, soldering sink wetting method” as described in Test 12a GB5095.6. The test temperature is 245 ± 50C, the wetting time is 3±0.5s, 测试要求(Requirement) 沾锡面积≥90% The wetting area shall account for more than 90% of immersed area. L 耐焊接热 Resistance to soldering heat 插座焊接端及基座体应按中国部标： CB5095.6 的试验“12d：锡焊槽法耐锡焊热” 规定的方法进行试验 熔锡温度：265±5℃ 浸渍时间：10±1 秒 The welding terminal and matrix of socket shall tested following the method “resistance to soldering heat, soldering sink method” as described in 12d CB5095.6. soldering temperature: 265±50C,Soaking time: 10±1s. 绝缘体不应有明显的变形、破损、 焊接端不应脱落 After the test, plastic matrix shall not deform, the welding terminal shall not fall off. 3.5 耐久性能 Endurance performance 测试项目(Items) M 机械寿命 测试方法(Test method) 测试要求(Requirement) 试验后应无卡死现象 插座接触电阻： 测试前≤30 mΩ 测试后≤50 mΩ 在量出插座接触电阻之后其次： Mechanical 插拔次数：10000 次 service life After testing the contact resistance, the socket shall be able to endure 10000 *******电子有限公司 ***** ELECTRONICS CO.,LTD
times of uncharged action test. 1. After the test, no sticking occurs, contact resistance shall meet requirements. 2. The contact resistance should be ≤30 mΩ, before test, ≤50 mΩ after test. 5．注意事项 Attentions:
5.1 装有产品的纸箱或木箱允许用任何方法运输，唯需避免雨雪直接淋袭和机械撞击。
The products packaged in cartons or wooden cases are allowed to move or transport in anyway, yet shall prevent any exposure in rainfall, snowfall and prevent any echanical damage.
5.2 产品应存放在环境温度为-10～+40℃，相对湿度不大于80%，周围空气不应有酸 、碱、硫化物、臭氧、氨气及其它对产品有害气体的仓库存。
The products shall be stored in the warehouse where temperature is within –10~400C, relative humidity below 80%, and there are no acidic, alkalescent, sulfide, ozone, alkaline air or any other corrosive gas in ambient environment,
因篇幅问题不能全部显示，请点此查看更多更全内容