RICOH AFICIO 200
CODICE DESCRIZIONE SC120 Scanner home position SC121 SC122 SC123 SC192
Scanner home position Scanner home position Scanner home position
Automatic SBU Adjustment error. POSS: Iamp, Dirty White Plate, Lamp Regulator, SBU
SC302 Charge Roller Current Leak SC306
Charge Roller Home Position
SC320 Polygon motor SC321 No Laser Start Signal SC322 Laser Sync Error SC324 SC390 SC391 SC393 SC402 SC411 SC500 SC503 SC504 SC506 SC542 SC546 SC547 SC610 SC691 SC692 SC900 SC92O SC921 SC980 SC981 SC990
LD drive current over TD Sensor Error 1 Developer Bias Leak TD Sensor Error 2 Transfer Roller Leak Separation Bias Error Main Motor
Upper Paper Tray Lift Motor –OPTIONAL PAPER TRAY UNIT Lower Paper Tray LIft Motor –OPTIONAL PAPER TRAY UNIT Main motor –OPTIONAL PAPER TRAY UNIT Fuser warm up error
Fuser temp. not steady falls or increases 10 durring standby Zero cross signal POSS: power suppty, IOCSS, BICU Communication error between duplex and IOCSS Communication error between BICU and Fax Communication error between Printer and BICU Counter error – check fuse #5
Communication error between BICU and MSU MSU Hardware error POSS: front door safety switch Program Loading Error POSS BICU, ROM NVRAM Clear error
Communication error between IOCSS and BICU
SC401 Transfer Roller Leak
SC543 Fuser over temp
Enter service mode (SP) --HoId the (C/S) Button for 4 seconds then enter 1 --- O ----7 --- (C/S), Exit service mode: by pressing (C/S) three times.
Reset fuser and some other error codes by Enter SP 5-810 and select 1 press and hold photomode key while holding photomode key press (#) key
Failing polygon (SC320) motor usually caused by overheating because of defective cooling fan.SC503/504 tray
Lift motor malfunction (SC503,5O4) First check for paper behind the trays otherwise open the combined lift motor of the paper tray unit and you will see one of the wires from the liftmotor is broken from the contact.
RICOH AFICIO 250
CODICE DESCRIZIONE SC101 Scan Lamp Error SC120 SC121 SC122 SC123 SC192
Scanner home position Scanner home position Scanner home position Scanner home position
Automatic SBU Adjustment error. POSS: Iamp, Dirty White Plate, Lamp Regulator, SBU
SC302 Charge Roller Current Leak SC306
Charge Roller Home Position
SC320 Polygon motor SC321 No Laser Start Signal SC322 SC324 SC390 SC391 SC393 SC4O1 SC402
Laser Sync Error LD drive current over TD Sensor Error 1 Developer Bias Leak TD Sensor Error 2 Transfer Roller Leak Transfer Roller Leak
SC411 Separation Bias Error SC500 Main Motor SC503 SC504 SC506 SC542 SC546 SC547 SC548 SC549 SC610 SC681 SC682 SC691 SC692 SC900 SC920 SC921 SC980 SC981 SC990
Upper Paper Tray Lift Motor -- optional paper tray unit Lower Paper Tray LIft Motor -- optional paper tray unit Main motor -optional paper tray unit Fuser warm up error
Fuser temp. not steady falls or increases 10 durring standby Zero cross signal POSS: power supply, IOCSS, BICU Fuser Edge Temp High POSS: Thermistor or PSU Fuser Edge Temp Low POSS: Thermistor or PSU Communication error between duplex and IOCSS Wrong Fax Option Wrong Print Option
Communication error between BICU and Fax Communication error between Printer and BICU Counter error
Communication error between BICU and MSU MSU Hardware error POSS: front door safety switch Program Loading Error POSS BICU, ROM NVRAM Clear error
Communication error between IOCSS and BICU
SC543 Fuser over temp
Enter service mode (SP) --HoId the (C/S) Button for 4 seconds then enter 1 --- O ----7 --- (C/S), Exit service mode: by pressing (C/S) three times.
Reset fuser and some other error codes by Enter SP 5-810 and select 1 press and hold photomode key while holding photomode key press (#) key
RICOH AFICIO 1035/1045
CODICE DESCRIZIONE
SC101 Exposure Lamp Error SC120 SC121 SC130 SC131 SC302 SC304 SC320 SC321 SC323 SC326 SC327 SC328 SC329 SC350 SC351 SC352 SC353 SC354 SC390 SC391 SC395 SC402 SC403 SC405 SC440 SC490 SC492 SC501 SC502 SC503 SC504 SC506 SC507 SC510 SC541 SC542 SC544 SC545 SC546
Scanner home position error I Scanner home position error 2 SBU defective
F-Gate asserts during shading Charge roller current leak
Charge roller current correction error Polygon motor error
No Laser Start Signal, F-Gate error LD drive current over
2nd laser synchronization error LD unit home position error 1 LD unit home position error 2 LD unit beam pitch misadjusted ID sensor pattern test error ID sensor VSG test error
ID sensor, pattern edge detect error
ID sensor, LED current abnormal at initialization ID sensor timeout abnormal adjustment TD Sensor Error
TD Sensor Auto Adjust Error
Development output abnormal, developer bias leak Transfer Roller Open
Transfer belt error: position, drive Transfer belt error: drive, sensor Main Motor Exhaust fan Cooling fan
1st Paper Tray Lift 2nd Tray Iift malfunction
3rd Tray Iift malfunction – OPTIONAL PAPER TRAY UNIT Lower Paper Tray Lift – OPTIONAL PAPER TRAY UNIT Main motor – OPTIONAL PAPER TRAY UNIT LCT Main motor lock LCT Lift malfunction Thermistor open Fuser warm up error Fuser over temp
Fusing Iamp remains on: Thermistor out of position Fusing temperature unstable
SC322 first laser synchronization error
SC401 Transfer Roller Leak
SC543 Fuser over temp
SC547 SC548 SC599 SC601 SC610 SC611 SC612 SC620 SC621 SC623 SC624 SC626 SC627 SC630 SC640 SC641 SC670 SC672
Zero cross signal POSS: power supply No Fuser lnstalled
Optional Output bin motor lock
Communication error between BICU and Scanner Unit Communication timeout error between ADF and BICU Communication break error between BICU and ADF Communication command error between BICU and ADF Communication timeout error between BICU and Finisher Communication timeout error between BICU and Finisher Communication timeout error between BICU and paper tray unit Communication break error between BICU and Paper Tray Unit Communication timeout error between BICU and LCT Communication break error between BICU and LCT Communication failure with CSS BICU control data transfer sum-check BICU control data transfer abnormal Engine Response error
Operation panel communication error
SC690 BICU SC691 BICU SC692 BICU SC700 SC701 SC722 SC724 SC725 SC726 SC727 SC729 SC730 SC732 SC733 SC744
ADF Pickup error ADF Pickup Lift error Finisher jogger motor error staple motor error
Finisher stack feed-out motor error Finisher shift tray 1 Iift motor error Finisher stapler rotation motor error Finisher punch motor error
Finisher stapler positioning motor error Finisher upper tray shift motor error Finisher lower tray Iift motor error Finisher lower tray shift motor error
SC731 Finisher exit guide motor
SC800 Control Board Defective SC804 Control Board Defective SC819 Software Error
SC820 SeIf-Diagnostic Error: CPU SC821 SeIf-Diagnostic Error: ASIC SC822 SeIf-Diagnostic Error: HDD SC823 SC824 SC826 SC827 SC828 SC829 SC835 SC836 SC837
SeIf-diagnostic Error: NIB SeIf-diagnostic Error: NVRAM
SeIf-diagnostic Error: Optional NVRAM SeIf-diagnostic Error: RAM SeIf-diagnostic Error: ROM SeIf-diagnostic Error: Optional RAM SeIf-Diagnostic Error: Parallel Interface SeIf-diagnostic Error: Resident Font SeIf-diagnostic Error: Optional Font
SC838
SC850 CS51
SeIf-diagnostic Error: Clock Generator
Network l/F
IEEE 1394 l/F Abnormal Hard Disk Error Hard Disk Error
SC860 SC865
SC900 Counter error Electronic SC901 Counter Mechanical SC951
F-gate error at write request
SC953 Software defective SC954 Software defective SC955 Software defective SC964 Software defective SC984 SC985 SC990
Print image data transfer error: Controller Board Scanner image data transfer error: Controller Board Software defective
SC986 Software defective SC991 Software defective SC996 FCU board error SC997 Software defective SC998 Software defective SC999
Program download error
Enter service mode(SP): Press the clear mode key. enter 1-0-7 hold down the c/s for three seconds. To enter the special service mode hold the # key down while pressing Copy SP.
Exit service mode: by pressing exit twice
Reset fuser and some other error codes by Entering the sp mode and cycling the power.
RICOH AP3800/828 – GESTETNER DSc38 - SAVIN SLP38c
CODICE DESCRIZIONE
Serial Number Mismatch SC195
SC201 Polygon motor SC220 SC221 SC230 SC231 SC240 SC260 SC261 SC285
SC370 SC371 SC372 SC373 SC374 SC375 SC376 SC377 SC380 SC381 SC385
Synch. detection signal error 1 (001: Y), (002: M), (003: C), (004: K) Synch. detection signal error 2 (001: Y), (002: M), (003: C), (004: K) FGATE error: (001: Y), (002: M), (003: C), (004: K) FGATE Timeout: (001: Y), (002: M), (003: C), (004: K) LD over (001: Y), (002: M), (003: C), (004: K) LD HP sensor not switched on (for K only) LD HP sensor not switched on (for K only) Line position adjustment (MUSIC) error TD sensor (K): Adjustment Error TD sensor (Y): Adjustment Error TD sensor (C): Adjustment Error TD sensor (M): Adjustment Error Vt error (K) Vt error (Y) Vt error (C) Vt error (M) Kdev. motor error Color dev. motor error ID sensor VSG adjustment Development gamma error (K) Development gamma error (Y)
SC386 SC387
SC388 Development gamma error (C) SC389 Development gamma error (M) SC390
Development Bias output
SC391-01 Charge AC: output error SC460-001 Thermistor 1(open circuit) SC460-002 Thermistor 1(short circuit) SC461-001 SC461-002 SC471 SC490
Thermistor 2 (open circuit) Thermistor 2 (short circuit) transfer belt H.P.
Transfer bias paper attraction roller bias leak
SC501 Paper Tray 1 SC502 Paper Tray 2 SC503-01 SC501-02
Tray 3 error (Paper Feed Unit or LCT) Tray 3 error (Paper Feed Unit or LCT)
SC504-01 Tray 4 error SC504-02 Tray 4 error SC530 Fusing fan SC541 SC542 SC543 SC544
Heating roller thermistor Heating roller warm-up error Heat roller Iamp overheat
Heating roller fusing Iamp 10w temp
SC545 SC546 SC551 SC553 SC554 SC555 SC556
Heat roller Iamp Short
Heat roller fusing Iamp temperature fluctuation Pressure roller thermistor
Pressure roller fusing Iamp over temp Pressure roller fusing Iamp Iow temp Pressure roller fusing Iamp short
Pressure roller fusing Iamp temp fluctuation
SC552 Pressure roller warm-up
SC560 Zero cross
SC621 Finisher/mailbox communication SC622 Bank communication SC623 SC640 SC641 SC670 SC687
Duplex unit communication BCU - Controller communication BCU —Controller communication No response from BCU at power on Memory address command
SC680 BCU/ MUSIC communication SC722 Finisher jogger motor SC724 Finisher staple hammer motor SC725 Finisher stack feed-out motor SC726 SC727 SC729 SC731 SC732 SC733 SC734 SC835
Finisher shift tray 1 Iift motor Finisher stapler rotation motor Finisher punch motor
Finisher exit guide plate motor Finisher tray 1 shift motor Finisher tray 2 Iift motor Finisher tray 2 shift motor Centronics interface
SC730 Finisher stapler motor
SC818 Software SC836 Font ROM SC837 Font ROM SC850 Network interface SC851 EEE 1394 SC860 HDD SC861 HDD SC863 HDD SC864 HDD SC865 HDD SC900 Electroctronic counter error SC990 Defective software SC998
Application start error
RICOH AFICIO 180/150
CODICE DESCRIZIONE SC122 Scanner home position SC320 Polygon motor SC322 Laser Sync Error SC402 SC542 SC544 SC546 SC547 SC620 SC691
High Voltage Leak Transfer or Charge Fuser warm up error Fuser Iow temp Fuser temp. not steady
Zero cross signal POSS: power supply, Fuser ground strap touching Iamp Communication error between BICU & ADF. Communication error between BICU and Fax
SC543 Fuser over temp
SC901 Counter error --check fuse #4
Fuser reset procedure: SP5-810 select 1, press and hold the photo mode key and then press and hold the enter key and wait for 5 beeps.
0-00 DIS or NSF not detected - Check connections to fax pcb and BICU
0-01 DCN received unexpectedly - Remote fax stopped TX
0-03 incompatible modem at other end - Check remote fax
0-21 EOL signal from other end not received: change G3 switch 0A bit 4 to a 1
A4 fax print on two pages: set printer switch 03, bit 0 to 1 and printer switch 04 to 00111111
Counter inizialize: SP mode 7-825
Disable speaker - set G3 switch “00” bit 0 and 1 to 0
Envelope ard bypass printing - set paper in user tools/printer/job control/paper input /bypass/standard
DF jams, no paper present: Can be caused by excessive light
Fax option not recognized - Turn on SW3 turn off SW1
APS through ADF, reads wrong size - Clean Sliding electrodes on bottom of DF
Maintenance Call Reset - SP7-909
Printer alarm light: reset PM counter SP7-909 / Reset PM display SP5-908
RICOH AFICIO 1027/1022
CODICE DESCRIZIONE
SC101 Exposure Iamp SC120 SC121 SC122 SC123 SC144 SC191 SC193
Scanner home (no detect) Scanner home (doesn’t leave) Scanner detects early home Scanner doesn’t return home
Communication between SBU and IPU PCB IPU board incorrect for machIne Error Image transfer (IPU Defective)
SC192 SBU adjustment error
SC195 DFGATE (ADF Communication) SC196 DFGATE (ADF Communication) SC197 DFGATE (ADF Communication) SC198 SC199
Memory address (firmware, SBCU, IPU) DF scanning (ADF, SBCU, Firmware)
SC302 Charge Leak SC320 Polygon motor SC322 Laser synchronization SC323
LD drive current over
SC355 ID sensor SC389 TD sensor SC390 TD sensor
SC391 Development bias leak SC392
TD sensor initial setting failure
SC401 Transfer Leak SC402 Transfer Leak SC411 Separation leak SC490 SC501 SC502 SC503 SC504 SC506 SC508 SC509 SC510
Toner supply motor 1st paper tray lift 2nd paper tray Iift 3rd paper tray Iift 4th paper tray Iift Paper tray motor lock Rear fence drive (LCT) Side fence drive (LCT) LCT Iower limit
SC500 Main motor
SC520 Paper tray
SC541 Thermistor open (fuser) SC542
Warm-up error (fuser)
SC543 Overheat (fuser) SC544 Overheat (fuser) SC545 SC546 SC548
Lamp remains on (fuser) Unstable temperature (fuser) Copier does not detect fuser
SC547 Zero cross
SC590 Exhaust fan SC611 SC612 SC620 SC621 SC630 SC640 SC641 SC650 SC672
Communication error between SBCU and ADF Communication error between SBCU and ADF Communication error between SBCU and finisher Communication error between SBCU and finisher Communication failure with CSS SBCU Error (control PCB or SBCU) SBCU Error (control PCB or SBCU)
Communication error between SBCU and duplex Communication error controller and op panel
SC670 Engine response SC720 Finisher ogger motor SC722 Finisher jogger motor SC724 Finisher stapler motor SC725 Finisher stack feed motor SC726 Finisher Iift motor
Finisher stapler motor SC727
SC728 Finisher stack SC730 SC731 SC770 SC791
Finisher stapler motor (movement) Output tray motor Shift tray motor
Communication error between SBCU and Bridge
SC732 Finisher shift motor
SC792 Finisher connection SC793 Interchange communication SC800 Controller board SC804 Controller board SC818 SC820
Watchdog error (Controller board) CPU error or Firmware
SC819 Firmware SC821 Controller board SC822 HardDrive SC823 Network Card SC824 NVRAM SC826 NVRAM SC827 Firmware SC828
Controller board or firmware
SC829 Optional memory SC835 Parallel Interface SC836-838 SC851 SC865 SC900 SC951 SC954
FONT Controller board IEEE 1394 I/F Hard drive or controller
Electronic total counter over 10 mil-yeah right replace nvram on controller Firmware or SBCU
Printer setting error (Firmware, IPU, or Controller)
SC850 Network Card SC860-864 Hard drive
SC901 Mechanical counter SC953 Firmware SC955 SC964 SC984
Memory setting error (Firmware, IPU, or Controller) Printer Ready error (Firmware, IPU, or Controller) data transfer error (Controller or SBCU)
SC986 Firmware SC900 Firmware SC991
Software error Iogged
SC996 FCU SC997 Firmware SC998
Firmware
SC999 Firmware download error
Enter service mode (SP): Press the clear mode key. enter 1-0-7 hold down the c/s for three seconds.
Reset Fuser: Enter SP mode and cycle power
SP5-801 Memory All Clear
因篇幅问题不能全部显示,请点此查看更多更全内容